Just How to Install a Bath Tub Yourself: Removing as well as Replacing.
Just How to Install a Bath Tub Yourself: Removing as well as Replacing.
Blog Article
Have you been trying to locate tips about A Step-by-Step Guide to Installing a Bathtub?
Mounting a bath tub isn't specifically brain surgery, however it does call for strong plumbing, woodworking, and sometimes, tiling skills. Replacing an old tub with a new one is likewise a reasonably tough task. If the old bathtub is conveniently obtainable, the project can move speedily; if you have to open a wall to remove the old tub and position the new bathtub, the job is a lot harder. In either instance, the task is within a residence handyman's abilities, although you will certainly require an assistant to leave the old tub as well as set in the new one. Make sure you have qualified on your own for the work and also fit trying it. As opposed to employing a professional to take over a halfway-completed project, it is better to consider utilizing one prior to you start. Possibilities are you might need an expert plumber to make tube connections.
This write-up will certainly aid you mount a brand-new tub in your restroom if you have already acquired a brand-new bathtub and don't require to alter the plan of your previous supply of water pipes.
Your devices as well as material checklist need to make up the following:
Getting ready for the Installment
First of all, the supporting structure supplied with the bathroom must be fitted (if needed) according to the supplier's directions. Next, fit the faucets or mixer to the tub. When fitting the faucet block, it is very important to ensure that if the faucet includes a plastic washer, it is fitted in between the bath and also the faucets. On a plastic bath, it is additionally practical to fit a sustaining plate under the faucets unit to stop strain on the bath tub.
Fit the versatile tap ports to the bottom of the two faucets using 2 nuts and also olives (in some cases supplied with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet hole, and afterwards pass the outlet with the hole in the bath. Utilize the nut supplied by the maker to fit the plug-hole. Examine the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next off, fit the end of the versatile overflow pipeline to the overflow outlet. Afterwards, screw the pipe to the overflow face which need to be fitted inside the bath. Make certain you make use of all of the provided washers.
Attach the trap to the bottom of the waste electrical outlet on the bath tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the catch to the electrical outlet. Link all-time low of the overflow tube in a similar manner.The bathroom need to now prepare to be fitted in its final placement.
Removing Old Taps
If you need to change old taps with new ones as a part of your installment, then the first thing you must do is separate the supply of water. After doing so, activate the taps to drain any kind of water remaining in the system. The process of getting rid of the existing taps can be quite troublesome as a result of the restricted gain access to that is usually the case.
Utilize a container wrench (crowsfoot spanner) or a faucet tool to undo the nut that attaches the supply pipelines to the taps. Have a fabric all set for the continuing to be water that will come from the pipelines. As soon as the supply pipelines have been eliminated, utilize the very same device to loosen the nut that holds the taps onto the bath/basin. You will certainly require to quit the solitary taps from turning during this procedure. As soon as the faucets have been removed, the holes in the bath/basin will need to be cleaned up of any kind of old securing compound.
Before proceeding to fit the new faucets, contrast the pipe connections on the old taps to the new faucets. If the old faucets are longer than the brand-new faucets, after that a shank adapter is required for the new taps to fit.
Installing the Tub
Utilizing both wood boards under its feet, position the bath tub in the called for placement. The wood boards are helpful in evenly spreading the weight of the bathtub over the area of the boards instead of focusing all the weight onto four little points.
The next goal is to make sure that the tub is leveled all round. This can be accomplished by checking the spirit level and adjusting the feet on the bathtub until the spirit level reads degree.
To mount faucets, fit all-time low of the outermost adaptable faucet port to the proper supply pipe by making a compression join; then do the same for the other tap.
Activate the water as well as inspect all joints as well as new pipework for leaks and tighten them if essential. Load the bath tub as well as likewise check the overflow outlet and the regular electrical outlet for leakages.
Lastly, repair the bath paneling as defined in the supplier's user's manual. Tiling as well as sealing around the bath tub needs to wait up until the tub has been made use of at the very least when as this will settle it right into its last position.
Fitting New Touches
If the tails of the new taps are plastic, after that you will certainly need a plastic connector to stop damages to the thread. One end of the adapter fits on the plastic tail of the faucet as well as the other end gives a link to the existent supply pipelines.
If you require to fit a monobloc, then you will certainly call for decreasing couplers, which connects the 10mm pipeline of the monobloc to the conventional 15mm supply pipe.
Next off, place the tap in the placing hole in the bath/basin ensuring that the washing machines are in place in between the tap and also the sink. Protect the tap in position with the producer provided backnut. When the tap is firmly in place, the supply pipelines can be linked to the tails of the taps. The faucets can either be connected by utilizing corrugated copper piping or with typical faucet ports. The former kind should be attached to the tap finishes first, tightening up only by hand. The supply pipelines can later be attached to the other end. Tighten up both ends with a spanner after both ends have been attached.
Tiling Around the Tub
In the location where the bath fulfills the ceramic tile, it is essential to seal the accompanies a silicone rubber caulking. This is essential as the installation can move sufficient to crack an inflexible seal, causing the water to permeate the wall between the bathroom and the tiling, bring about complications with wetness and possible leakages to the ceiling below.
You can select from a variety of coloured sealants to assimilate your fixtures as well as installations. They are sold in tubes as well as cartridges, and also are capable of securing voids as much as a size of 3mm (1/8 inch). If you have a bigger gap to load, you can load it with twists of drenched paper or soft rope. Remember to constantly load the bathtub with water before sealing, to enable the activity experienced when the bathtub is in use. The sealant can break relatively very early if you do not take into account this movement before sealing.
Additionally, ceramic coving or quadrant floor tiles can be used to edge the bath or shower tray. Plastic strips of coving, which are easy to use as well as reduce to dimension, are additionally conveniently readily available on the market. It is advisable to fit the tiles utilizing water-resistant or water resistant sticky as well as cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
As a reader about Tools You Need to Install a New Bathtub , I figured sharing that editorial was worthwhile. Don't hesitate to take a moment to promote this post if you enjoyed it. I am grateful for your time. Don't forget to come by our blog back soon.
Free Quote Report this page